Bass Cab
Check out this page if you are looking for Bass Cab
|
Gallien-Krueger 112Mbx Extension Cab For Micro Bass
$299
The Gallien-Krueger 112MBX Extension Cab for Micro Bass lets you hang on to your portability while extending the output of your MB150S or MB150E combo amp. At just 12 lbs., this small but mighty Gallien-Krueger speaker cabinet shares the same sealed aluminum chassis, steel grille, and 100W speaker with the combos. The optional MB Mic Kit lets you mount the 112MBX on your mic stand for greater projection. Gallien-Krueger gives you a 1-year warranty on speaker and a 2-year warranty on electronics with the 112MBX.12 lbs. Aluminum chassis Steel grille 100W speaker Optional MB Mic Kit lets you mount the 112MBX on your mic stand for greater projection
|
|
Swr Big Ben Bass Speaker Cab Cover
$19.99
Protect your investment with this heavy-duty Cordura speaker cover tailored to fit your SWR Big Ben bass speaker cabinet perfectly. Features an SWR logo on the face.
|
|
Markbass Traveler 102P 400W 2X10 Special Edition Bass Cab
$649.99
The Markbass Traveler 102P 400W 2x10 Special Edition Bass Cab is one of the smallest and lightest 2x10" cabinets on the market. It can be used in either a vertical or horizontal position with the rear port affecting the overall sound differently depending on which setup you choose. If the sound is too boomy, go vertical. For more bass, go horizontal. With a punchy, full-range sound, this cab will look great too with the Special Edition Markbass Little Mark III.All Markbass cabinets contain ultra-light neodymium speakers. The Traveler 102P was introduced in 2005 and has been one of the top-selling Markbass products ever since.Special edition finishUltra-light custom-designed neodymium 10" woofers1" piezo tweeter with attenuation controlCompact and sturdy enclosure with lightweight constructionRectangular rear vent impacts the sound differently depending on setupExceptional frequency response for its size
|
|
Genz-Benz Uber Bass 210T-UB Cab 8 Ohm
$959
The GB 210T-UB bass cabinet from Genz-Benz's Uber line is designed to the same demanding specifications and response characteristics as the larger Uber models. The 2 x 10" with tweeter cabinet delivers the dynamic Uber tone in the smallest possible speaker cab design. It features a cast frame GNX-10250 neodymium loudspeaker and compression bullet tweeter. The input panel provides both Speakon and 1/4" connections and a tweeter level control. Available in 8-ohm impedance only.
|
|
Aguilar GS 212 Bass Cab 8 ohm
$839
2 - 12" cast frame woofers with 56 oz. magnets handle up to 600W and give you a solid, defined deep bass. A phenolic tweeter with integral phase plug lets you dial in just the right amount of edge. Neutric Speakon and 1/4" inputs. Recessed handles. Interlocking corners. 24"H x 22-1/2"W x 16-5/8"D. Includes removable casters.
|
|
Aguilar GS 212 Bass Cab 4 ohm
$839
2 - 12" cast frame woofers with 56 oz. magnets handle up to 600W and give you a solid, defined deep bass. A phenolic tweeter with integral phase plug lets you dial in just the right amount of edge. Neutric Speakon and 1/4" inputs. Recessed handles. Interlocking corners. 24"H x 22-1/2"W x 16-5/8"D. Includes removable casters.
|
|
Gallien-Krueger 410Rbh 800W 4X10 Bass Cab With Horn
$899
The Gallien-Krueger 410RBH 800W 4x10 Bass Cab with Horn is a perfect cab to pair with the 400RB head. 8- or 4-ohm operation. 800W handling. 4 cast-frame 10" speakers plus horn. Switchable between biamp, full range with built-in horn power limiter for protection. The 410RBH cab is made of birch with black carpet covering, a 16-gauge steel grille, interlocking corners, nickel-plated casters, and dual front-loaded ports. 27-1/2"W x 23"H x 18"D. 92 lbs. 1-year warranty on speakers. 2-year warranty on electronics. 8- or 4-ohm operation 800W handling 4 cast-frame 10" speakers plus horn Switchable between biamp, full range Built-in horn power limiter for protection Birch cabinet Black carpet covering 16-gauge steel grille Interlocking corners Nickel-plated casters Dual front-loaded ports 27-1/2"W x 23"H x 1"D 92 lbs. 1-year warranty on speakers 2-year warranty on electronics
|
|
Genz-Benz Uber Bass 210T-Ub Cab 8 Ohm
$959
The GB 210T-UB bass cabinet from Genz-Benz's Uber line is designed to the same demanding specifications and response characteristics as the larger Uber models. The 2 x 10" with tweeter cabinet delivers the dynamic Uber tone in the smallest possible speaker cab design. It features a cast frame GNX-10250 neodymium loudspeaker and compression bullet tweeter. The input panel provides both Speakon and 1/4" connections and a tweeter level control. Available in 8-ohm impedance only. Uber tone in a compact package 2 - 10" neodymium magnet cast frame speakers Compression bullet tweeter with level control Speakon and 1/4" connectors
|
|
Aguilar Gs 212 Bass Cab 8 Ohm
$839
2 - 12" cast frame woofers with 56 oz. magnets handle up to 600W and give you a solid, defined deep bass. A phenolic tweeter with integral phase plug lets you dial in just the right amount of edge. Neutric Speakon and 1/4" inputs. Recessed handles. Interlocking corners. 24"H x 22-1/2"W x 16-5/8"D. Includes removable casters.2 - 12" cast frame woofers with 56 oz. magnets Power handling: 600 watts Impedance: available in 4 or 8 ohms Phenolic tweeter with integral phase plug Custom crossover with variable tweeter control One Neutrik Speakon and 2 - 1/4" inputs Frequency response: 41 Hz to 16 kHz Sensitivity: 103 dB @ 1W 1M Casters included Recessed deep-dish handles Interlocking corners 7-ply, void-free Philippine mahogany Weight: 70 lbs. 3-year limited warranty
|
|
Aguilar Gs 212 Bass Cab 4 Ohm
$839
2 - 12" cast frame woofers with 56 oz. magnets handle up to 600W and give you a solid, defined deep bass. A phenolic tweeter with integral phase plug lets you dial in just the right amount of edge. Neutric Speakon and 1/4" inputs. Recessed handles. Interlocking corners. 24"H x 22-1/2"W x 16-5/8"D. Includes removable casters.2 - 12" cast frame woofers with 56 oz. magnets Power handling: 600 watts Impedance: available in 4 or 8 ohms Phenolic tweeter with integral phase plug Custom crossover with variable tweeter control One Neutrik Speakon and 2 - 1/4" inputs Frequency response: 41 Hz to 16 kHz Sensitivity: 103 dB @ 1W 1M Casters included Recessed deep-dish handles Interlocking corners 7-ply, void-free Philippine mahogany Weight: 70 lbs. 3-year limited warranty
|
|
Acoustic B200H 200W Bass Head and B115 250W 1x15 Bass Cab Package
$399.99
Now get both the Acoustic B200H Bass Amp Head and the Acoustic B115 1x15 Bass Speaker Cabinet as a package deal. With these 2 monsters in your arsenal, there's no venue you can't shake up. The B200H 200W Bass Head: The Acoustic B200H professional bass amp head is designed for large club and live applications where it will fill any stage with depth and definition. Used in conjunction with the B115 bass speaker cab, the B200H is a bass amp head that will easily drive either 1 or 2 cabinets in any combination of your choice. The 2 bass inputs are designed to accommodate both active and passive bass instruments while the Gain and Volume controls give you complete control over the character of your tone. Increase the gain for some old school rock tones, or lower it and turn up the volume for great clean, classic or funk tones. The preamp includes a very natural and tube-like compression as well as a harmonically rich distortion circuit, which keeps your tone musical—even at high volume levels. The B200H bass amp also includes a notch filter to tailor your mids, and a 6-band EQ for exact control over every nuance of your bass's tone. Rear panel features include a parallel Effects Loop, and XLR balanced Line Out with Level Control and Ground Lift. The 2 speaker output jacks allow you to directly connect to each speaker enclosure (such as the B115 and/or B410) to maximize your tone and power. The B115 250W 1x15 Bass Cabinet The Acoustic B115 bass speaker cabinet has a professional enclosure designed for large clubs and live applications. Used in conjunction with the Acoustic B200H bass amp head, the B115 cabinet will easily handle the power of your amplifier and provide wall-shaking lows and a massive bottom end. Although conservatively rated at 250W RMS, any combination of Acoustic B115 or B410 speaker cabinets may be used for larger venues. The B115 bass cabinet features a rock-solid, tuned and ported design with heavy internal bracing, caster sockets and professional spring-loaded touring handles with rubber grips. Heavy-duty rubber feet allow secure stacking and ensure solid placement on any floor surface. Rear panel features include a recessed jackplate with parallel dual 1/4" jacks and a horn on/off switch. Classic Acoustic cosmetics include nickel corners, black grille cloth with white piping, heavy-duty roadworthy covering material, and steel trim strips with understated blue accent color. It all adds to the durability (and legacy vibe) of this great bass speaker cabinet.
|
|
Markbass Bass Keeper Strap
$19.99
Never again do you have to worry about leaning your bass against your cab only to have it bumped and losing your favorite axe when the neck cracks from the fall. With the Bass Keeper strap, when you're not using your guitar, it's securely fastened with Velcro straps that attach to the side or handle of your cab and around the neck of the guitar. It'll comfortably rest there so you can rest easy too. It's also a great way to store your back up bass during a gig.Attaches to handle or side of cab Velcro straps go around neck of bass
|
|
Acoustic B200h 200W Bass Head And B115 250W 1X15 Bass Cab Package
$399.99
Now get both the Acoustic B200H Bass Amp Head and the Acoustic B115 1x15 Bass Speaker Cabinet as a package deal. With these 2 monsters in your arsenal, there's no venue you can't shake up. The B200H 200W Bass Head: The Acoustic B200H professional bass amp head is designed for large club and live applications where it will fill any stage with depth and definition. Used in conjunction with the B115 bass speaker cab, the B200H is a bass amp head that will easily drive either 1 or 2 cabinets in any combination of your choice. The 2 bass inputs are designed to accommodate both active and passive bass instruments while the Gain and Volume controls give you complete control over the character of your tone. Increase the gain for some old school rock tones, or lower it and turn up the volume for great clean, classic or funk tones. The preamp includes a very natural and tube-like compression as well as a harmonically rich distortion circuit, which keeps your tone musical - even at high volume levels. The B200H bass amp also includes a notch filter to tailor your mids, and a 6-band EQ for exact control over every nuance of your bass's tone. Rear panel features include a parallel Effects Loop, and XLR balanced Line Out with Level Control and Ground Lift. The 2 speaker output jacks allow you to directly connect to each speaker enclosure (such as the B115 and/or B410) to maximize your tone and power. The B115 250W 1x15 Bass Cabinet The Acoustic B115 bass speaker cabinet has a professional enclosure designed for large clubs and live applications. Used in conjunction with the Acoustic B200H bass amp head, the B115 cabinet will easily handle the power of your amplifier and provide wall-shaking lows and a massive bottom end. Although conservatively rated at 250W RMS, any combination of Acoustic B115 or B410 speaker cabinets may be used for larger venues. The B115 bass cabinet features a rock-solid, tuned and ported design with heavy internal bracing, caster sockets and professional spring-loaded touring handles with rubber grips. Heavy-duty rubber feet allow secure stacking and ensure solid placement on any floor surface. Rear panel features include a recessed jackplate with parallel dual 1/4" jacks and a horn on/off switch. Classic Acoustic cosmetics include nickel corners, black grille cloth with white piping, heavy-duty roadworthy covering material, and steel trim strips with understated blue accent color. It all adds to the durability (and legacy vibe) of this great bass speaker cabinet. B200H Head: Extra goodies: Ground Lift Effect Loop Options: Power: 200 Watts @ 4 Ohms Speaker: 15" Heavy-duty speaker, built-in horn Channels: 1 EQ: 6-Band EQ - sweepable Frequency notch filter Inputs: dual inputs (passive & active) Outs: XLR direct out B115 Cabinet: Other goodies: Heavy-duty spring-loaded touring handles Damage-resistant vinyl covering Caster sockets Power: 250 watts power handling Speaker: 15" heavy-duty speaker, high-frequency horn with on/off
|
|
Gallien-Krueger 410Rbh/4 800W Bass Cab
$899
Gets a tight, punchy sound. It operates at eight or 4 ohms, handles up to 800W, and is loaded with 4 GK-Paragon cast-frame 10" speakers and a GK-Paragon HF horn. Switchable between full-range or biamp operation. Heavy-duty construction features an all-birch cabinet with black carpet covering, 16-gauge steel grille, nickel-plated casters, and a custom-tooled interlocking corner system. 23"W x 27.5"H x 18"D. 92 lbs. 1-year warranty on speakers. 2-year warranty on electronics.4-ohm operation800W handlingFour 10" cast-frame speakers and a GK-Paragon HF hornSwitchable between full-range or biamp operationFeatures all-birch cabinet constructionBlack carpet covering16-gauge steel grilleNickel-plated castersInterlocking corner system1-year warranty on speakers2-year warranty on electronics
|
*************************************************************
If you didn"t find what you wanted look below for Bass Cab in the Amazon Marketplace.
*************************************************************
 |
Acoustic B200H 200W Bass Head and B115 250W 1x15 Bass Cab Package
Sale Price: $399.99
|
|
|
Now get both the B200H bass head and B115 1x15 cabinet as a package deal. With these two monsters in your arsenal, there's no venue you can't shake up. The B200H 200W Bass Head: The Acoustic B200H professional head is designed for large club and live applications where it will fill any stage with depth and definition...
|
 |
Behringer Ultrabass BB410 1200W 4x10 Bass Cabinet
List Price: $719.99
Sale Price: $299.99
|
|
|
The Behringer BB410 Bass Cabinet's four 10" BUGERA speakers and a unique switchable 1" horn tweeter deliver 1,200 Watts with plenty of headroom to spare. One mighty package for tons of high impact and warmth...
|
 |
Ampeg Pro Neo PN-410HLF Bass Amp Cab, 4x10-inch speaker cabinet, neodymium loaded, 850W RMS
List Price: $1,539.99
Sale Price: $1,099.99
|
|
|
The Ampeg PN-410HLF features four 10-inch custom-designed U.S. Eminence® woofers that can deliver the massive low end provided by high-output Ampeg bass heads. The lightweight neodymium woofers and compression driver are housed within a rugged 15mm birch plywood enclosure and shielded by a tough, powder-coated metal grille...
|
 |
Ampeg B-410HE B Series 4x10 Bass Enclosure
List Price: $519.99
Sale Price: $399.99
|
|
|
With its four 10" speakers and 1" horn, the Ampeg B-410HE can really rock the house. Suitable for most sizes of venues, the 8-Ohm enclosure features heavy-duty recessed handles and detachable casters, making it supremely portable...
|
 |
Eden D410XST4 David Series XST Bass Cabinets
List Price: $1,787.48
Sale Price: $1,099.99
|
|
|
Our 1000 watt D410XST features a deeper,stronger low end than the XLT, and a more open, transparent midrange definition and exceptionally flat studio-like response along with reduced size and weight. The tone is wonderful, well-balanced with a smooth, effortless quality usually reserved for the studio...
|
 |
Ampeg SVT-410HE Classic Series 4x10 Bass Enclosure
List Price: $909.99
Sale Price: $649.99
Used From: $535.00
|
|
|
The Classic Series is all about the Ampeg SVT. We pioneered Super-Valve Technology in the 1960s and continue to offer the ultimate, top-performance gear to the world’s most demanding bassists. Looking for a speaker cabinet to brighten up your bottom-heavy bass rig? Or, maybe you’ve recently downsized your transportation to save a few bucks on fuel, and no longer have room to haul your beloved SVT-810E to the gig...
|
 |
Peavey Headliner 115 Bass Enclosure
List Price: $399.99
Sale Price: $245.99
Used From: $215.79
|
|
|
500 watts program power handling - 1,000 watts peak - 15" Sheffield(r) bass woofer - 18mm ply cabinet with internal bracing and steel corners - 16-gauge perforated metal grille - Durable black carpet covering - Two 1/4' input jacks and one NL4 four-pin receptacle - Vented cabinet for powerful bass
|
*************************************************************
What is needed to get a bass sound to that like Breaking Benjamin?
I have a nine band EQ bass cab, an active bass guitar, no effects, and play without a pick.
Probably a distortion or fuzz pedal.
Speaker Cab
Check out this page if you are looking for Speaker Cab
|
Randall Isolation 12 Speaker Cab
$399.99
Essential whenever or wherever you're unable to crank full performance volume and tone. The concept is simple. A speaker is mounted in a completely closed, hinged cabinet with a microphone suspended inside. The cab has 1/4" in and outs, as well as a mic out to the mixing console. For recording, Isolation lets you record your amp full out, reflecting your true tone without waking the neighbors or inspiring visits from the cops. 12" Celestion Vintage 30 speaker. 18"W x 18"H x 31-1/2"D.Retractable handle Celestion Vintage 30 - 12" speaker 10" gooseneck for mic support Mic not included, condenser mic recommended
|
|
Swr Big Ben Bass Speaker Cab Cover
$19.99
Protect your investment with this heavy-duty Cordura speaker cover tailored to fit your SWR Big Ben bass speaker cabinet perfectly. Features an SWR logo on the face.
|
|
Radial Engineering Cab-Bone Speaker Cabinet Switcher
$259.99
This guitar amp cabinet switcher connects between an amp head and 2 cabinets, allowing transition between the 2 cabs while using the same amp head.Uses high-performance, high-cycling, gold contact relays to switch the amp's speaker output without adding color to the tone. To ensure safe, stable amplifier operation and smooth transitions, a timer IC manages a ramped connection overlap. This ensures constant load on the output, a major concern with tube amplifiers. As a further safety measure, the Cab-Bone incorporates a power-off feature called SafeMode which automatically diverts the input signal to output-1 if the power supply is ever disconnected or turned off by mistake.To reduce the 'cable spaghetti' between the amplifier, speakers, pedal board and back, Cab-Bone is equipped with a Slingshot input and output. Slingshot is Radial's easy to use remote control system that allows any footswitch to toggle switching of remote devices using just regular 1/4" guitar cables. The Slingshot remote input can be controlled by either momentary or latching contact closure.To add versatility, the Cab-Bone also incorporates a Slingshot output that can be used to remotely switch amp channels while switching cabinets. You could, for instance, connect the Slingshot remote output on the Radial Loopbone to toggle the Cab-Bone and go from a 2 x 12" open back to a 4 x12" half-stack. Connecting the Slingshot output to the amp as well would allow you to change the amp channel at the same time, allowing each cabinet to have its own EQ and gain.Add a Loopbone to the equation and with a single foot stomp you can introduce an effects loop, change speakers and change amp channels at the same time! Very cool! Now you can get those perfect tone combinations onstage quickly, and do it with one switch instead of a tap dance routine!Like all Radial products, the Cab-Bone is built tough to handle the road: 14-gauge steel, baked enamel finish, and high performance parts throughout. You get all of this in a compact enclosure that is ultra-quiet and completely transparent to the tone of your amp.Cab-Boneanother creative tool for making better music from the Tonebone tone fanatics at Radial.Guitar amp speaker cabinet switcherLets you toggle between 2 speaker cabinetsDigitally controlled relays with ramping overlapSlingshot remote-control switchingSafeMode failsafe protectionWorks with tube and solid state amplifiers
|
|
ZT Lunchbox Cab 1X6.5 Passive Guitar Speaker Cabinet Silver
$119
The Lunchbox Cab is built on the platform of ZT's highly acclaimed Lunchbox amplifier. It's a Lunchbox without the amp—a passive extension speaker, with the same solid-as-a-brick cabinet housing the same custom-design 6.5" driver used in the ZT Lunchbox amp.Weighing less than 7 pounds, the Cab can blast out over 120dB, and sounds great doing it. The Cab also features a phase switch to provide accuracy in any situation.Connect the passive speaker cabinet to the Lunchbox amp's external speaker output and build a Lunchbox stack (it's adorable—like ferocious puppies or kittens). Or spread them apart a few feet to create spatial imaging. Or go further and put the ZT Cabs on opposite sides of the stage and give your sound a dimension that will make the crowd's heads swim.*Note: Early production Lunchbox amps (serial numbers LB02 0000 1000 through LB02 0000 2999) are not optimized for use with the Lunchbox Cab. Please verify that your Lunchbox is compatible before you add a cab, particularly if you expect to play at very high levels.
|
|
Zt Lunchbox Cab 1X6.5 Passive Guitar Speaker Cabinet Silver
$119
The Lunchbox Cab is built on the platform of ZT's highly acclaimed Lunchbox amplifier. It's a Lunchbox without the amp - a passive extension speaker, with the same solid-as-a-brick cabinet housing the same custom-design 6.5" driver used in the ZT Lunchbox amp.Weighing less than 7 pounds, the Cab can blast out over 120dB, and sounds great doing it. The Cab also features a phase switch to provide accuracy in any situation.Connect the passive speaker cabinet to the Lunchbox amp's external speaker output and build a Lunchbox stack (it's adorable - like ferocious puppies or kittens). Or spread them apart a few feet to create spatial imaging. Or go further and put the ZT Cabs on opposite sides of the stage and give your sound a dimension that will make the crowd's heads swim.*Note: Early production Lunchbox amps (serial numbers LB02 0000 1000 through LB02 0000 2999) are not optimized for use with the Lunchbox Cab. Please verify that your Lunchbox is compatible before you add a cab, particularly if you expect to play at very high levels.6-1/2" DriverPhase SwitchRugged exterior
|
|
Markbass Markacoustic Ac 101 Cab 200W 1X10 Acoustic Speaker Cabinet Black 8 Ohms
$499.99
The compact, lightweight Markbass AC 101 CAB acoustic speaker is designed for use with acoustic instruments. It allows you to get maximum power from your Markacoustic combo (as an extension cabinet) or the Markacoustic AH 250 head.Acoustic speaker: 1x10" Bass port: rear Impedance: 8 Ohms Speaker power handling: 200W RMS (AES Standard) Weight: 18-1/4lb. Height: 14-1/2"H x 14"W x 14-1/2"D
|
|
Yamaha C215v Dual 15 Club Concert Speaker Cab
$699.99
Like other members of the Club Concert series, the Yamaha C215V Dual 15" Club Concert Speaker Cab features refinements aimed at permanent installations. They feature an elastomeric spray coating that easily fits any decor, is very tough, and readily paintable to match surroundings. The steel grilles are foam-lined with acoustically transparent material to provide a more subdued appearance.Assembled by skilled technicians, each cabinet is designed for better low-end response and includes heavy steel handles and sturdy pole sockets to make moving and positioning easy. The custom drivers from Eminence feature high-strength curvilinear cones and Kapton voice coil formers, plus oxygen-free copper voice coils and oversize strontium ferrite magnets to provide high power handling and long life. 15" and 18" drivers use cast aluminum frames to support the massive magnet structure, eliminate flex, and dissipate heat.The titanium diaphragm compression driver is mated to a 90 degree x 40 degree custom-designed horn. Internal electronics feature an over-built crossover network and overload protection. Connections are dual Neutrik Speakon and 1/4" jacks. With professional features, excellent sonic performance, and great value, Club Concert Series loudspeakers deliver premium quality night after night.The S215V features dual cast-frame 15" drivers. Frequency response: (-10dB) 42Hz-16kHz. 1,000W program handling, 2,000W peak. Sensitivity: 99dB. 20"W x 46"H x 24"D. 101 lbs.Tough, paintable exterior coatingDual cast-frame 15" driversFrequency response: (-10dB) 42Hz-16kHz1,000W program handling, 2,000W peakSensitivity: 99dB20"W x 46"H x 24"D101 lbs.
|
|
Refurbished Yamaha C215v Dual 15 Club Concert Speaker Cab
$549.99
Like other members of the Club Concert series, the Yamaha C215V Dual 15" Club Concert Speaker Cab features refinements aimed at permanent installations. They feature an elastomeric spray coating that easily fits any decor, is very tough, and readily paintable to match surroundings. The steel grilles are foam-lined with acoustically transparent material to provide a more subdued appearance.Assembled by skilled technicians, each cabinet is designed for better low-end response and includes heavy steel handles and sturdy pole sockets to make moving and positioning easy. The custom drivers from Eminence feature high-strength curvilinear cones and Kapton voice coil formers, plus oxygen-free copper voice coils and oversize strontium ferrite magnets to provide high power handling and long life. 15" and 18" drivers use cast aluminum frames to support the massive magnet structure, eliminate flex, and dissipate heat.The titanium diaphragm compression driver is mated to a 90 degree x 40 degree custom-designed horn. Internal electronics feature an over-built crossover network and overload protection. Connections are dual Neutrik Speakon and 1/4" jacks. With professional features, excellent sonic performance, and great value, Club Concert Series loudspeakers deliver premium quality night after night.The S215V features dual cast-frame 15" drivers. Frequency response: (-10dB) 42Hz-16kHz. 1,000W program handling, 2,000W peak. Sensitivity: 99dB. 20"W x 46"H x 24"D. 101 lbs.Tough, paintable exterior coatingDual cast-frame 15" driversFrequency response: (-10dB) 42Hz-16kHz1,000W program handling, 2,000W peakSensitivity: 99dB20"W x 46"H x 24"D101 lbs.
|
|
Used Yamaha C215v Dual 15 Club Concert Speaker Cab 889406620117
$594.99
Like other members of the Club Concert series, the Yamaha C215V Dual 15" Club Concert Speaker Cab features refinements aimed at permanent installations. They feature an elastomeric spray coating that easily fits any decor, is very tough, and readily paintable to match surroundings. The steel grilles are foam-lined with acoustically transparent material to provide a more subdued appearance.Assembled by skilled technicians, each cabinet is designed for better low-end response and includes heavy steel handles and sturdy pole sockets to make moving and positioning easy. The custom drivers from Eminence feature high-strength curvilinear cones and Kapton voice coil formers, plus oxygen-free copper voice coils and oversize strontium ferrite magnets to provide high power handling and long life. 15" and 18" drivers use cast aluminum frames to support the massive magnet structure, eliminate flex, and dissipate heat.The titanium diaphragm compression driver is mated to a 90 degree x 40 degree custom-designed horn. Internal electronics feature an over-built crossover network and overload protection. Connections are dual Neutrik Speakon and 1/4" jacks. With professional features, excellent sonic performance, and great value, Club Concert Series loudspeakers deliver premium quality night after night.The S215V features dual cast-frame 15" drivers. Frequency response: (-10dB) 42Hz-16kHz. 1,000W program handling, 2,000W peak. Sensitivity: 99dB. 20"W x 46"H x 24"D. 101 lbs.Tough, paintable exterior coatingDual cast-frame 15" driversFrequency response: (-10dB) 42Hz-16kHz1,000W program handling, 2,000W peakSensitivity: 99dB20"W x 46"H x 24"D101 lbs.
|
|
Used Yamaha C215v Dual 15 Club Concert Speaker Cab 889406579200
$594.99
Like other members of the Club Concert series, the Yamaha C215V Dual 15" Club Concert Speaker Cab features refinements aimed at permanent installations. They feature an elastomeric spray coating that easily fits any decor, is very tough, and readily paintable to match surroundings. The steel grilles are foam-lined with acoustically transparent material to provide a more subdued appearance.Assembled by skilled technicians, each cabinet is designed for better low-end response and includes heavy steel handles and sturdy pole sockets to make moving and positioning easy. The custom drivers from Eminence feature high-strength curvilinear cones and Kapton voice coil formers, plus oxygen-free copper voice coils and oversize strontium ferrite magnets to provide high power handling and long life. 15" and 18" drivers use cast aluminum frames to support the massive magnet structure, eliminate flex, and dissipate heat.The titanium diaphragm compression driver is mated to a 90 degree x 40 degree custom-designed horn. Internal electronics feature an over-built crossover network and overload protection. Connections are dual Neutrik Speakon and 1/4" jacks. With professional features, excellent sonic performance, and great value, Club Concert Series loudspeakers deliver premium quality night after night.The S215V features dual cast-frame 15" drivers. Frequency response: (-10dB) 42Hz-16kHz. 1,000W program handling, 2,000W peak. Sensitivity: 99dB. 20"W x 46"H x 24"D. 101 lbs.Tough, paintable exterior coatingDual cast-frame 15" driversFrequency response: (-10dB) 42Hz-16kHz1,000W program handling, 2,000W peakSensitivity: 99dB20"W x 46"H x 24"D101 lbs.
|
|
Evh 5150 Iii 412 Speaker Cabinet Cover
$35
This multi-panel, super tough black 600d speaker cabinet cover from EVH is designed to fit over the EVH 5150 III 412 speaker cab. It comes embroidered with the EVH logo in white thread.
|
|
Kustom KPC12M 12IN Monitor Speaker Cab with Horn Pair
$239.98
The Kustom KPC12M 12" Monitor Speaker Cabinet uses a specially voiced crossover to ensure clear separation of frequencies for crisp, full-range reproduction. A 12" woofer delivers deep low frequencies, while a 6" x 12" horn produces bright high-end tones. The Kustom 12" monitor cabinet features 2 parallel input jacks, sturdy construction with reinforced corners and heavy-duty Tolex® covering. Flexible 30/60/90° positioning.
|
|
Kustom Kpc12m 12In Monitor Speaker Cab With Horn Pair
$239.98
The Kustom KPC12M 12" Monitor Speaker Cabinet uses a specially voiced crossover to ensure clear separation of frequencies for crisp, full-range reproduction. A 12" woofer delivers deep low frequencies, while a 6" x 12" horn produces bright high-end tones. The Kustom 12" monitor cabinet features 2 parallel input jacks, sturdy construction with reinforced corners and heavy-duty Tolex covering. Flexible 30/60/90 positioning.2 monitors12" woofer for deep bass tones6" x 12" horn for shimmering highsSpecially voiced internal crossover provides superb separation of frequenciesRubber strap handle1-3/8" polemount30/60/90 positioning
|
*************************************************************
If you didn"t find what you wanted look below for Speaker Cab in the Amazon Marketplace.
*************************************************************
 |
Vox V112TV 1X12" Guitar Speaker Cabinet Cream
List Price: $250.00
Used From: $156.00
|
|
|
The Vox V112TV speaker cabinet is fitted with a custom-made Celestion 12" speaker. Its sophisticated sound is unmistakably Vox, delivering that distinctively British top-end tone.As part of the modern classic guitar series, this guitar speaker cab was designed to compliment the AC4TVH head for powerful, vintage tone...
|
|
Ampeg Pro Neo PN-410HLF Bass Amp Cab, 4x10-inch speaker cabinet, neodymium loaded, 850W RMS
List Price: $1,539.99
Sale Price: $1,099.99
|
|
|
The Ampeg PN-410HLF features four 10-inch custom-designed U.S. Eminence® woofers that can deliver the massive low end provided by high-output Ampeg bass heads. The lightweight neodymium woofers and compression driver are housed within a rugged 15mm birch plywood enclosure and shielded by a tough, powder-coated metal grille...
|
 |
Orange Amplifiers PPC Series PPC212-C 120W 2x12 Guitar Speaker Cabinet Orange Straight
List Price: $1,029.00
Sale Price: Too low to display
Used From: $646.89
|
|
|
The 120W Orange Amplifiers PPC212-C guitar speaker cabinet is crafted using 13-ply high-density 18mm birch plywood throughout like every Power Projection Cabinet (PPC). Orange speaker enclosures, like Orange amplifiers, are built to last with manufacturing techniques that assure extremely rugged construction...
|
 |
Celestion Vintage 30 Guitar Speaker, 8 Ohm
List Price: $215.00
Sale Price: $145.00
Used From: $129.99
|
|
|
Equipped with the "H" magnet this revealing speaker provides enormously detailed and rich overtones accompanied by a warm low end, rich vocal mid range and a beautiful top end compliment.
|
*************************************************************
What are the speaker sizes in my 2005 dodge dakota quad cab?
I heard that the sizes were 6 1/2 by 6 3/4 and the back are 6 by 9. Is this right?
Go to Crutchfield.com- they should be able to help comfirm this.
Cab Road
Check out this page if you are looking for Cab Road
*************************************************************
For More choices check out Cab Road some of our other merchants.
*************************************************************
|
Radial Engineering Cab-Bone Speaker Cabinet Switcher
$259.99
This guitar amp cabinet switcher connects between an amp head and 2 cabinets, allowing transition between the 2 cabs while using the same amp head.Uses high-performance, high-cycling, gold contact relays to switch the amp's speaker output without adding color to the tone. To ensure safe, stable amplifier operation and smooth transitions, a timer IC manages a ramped connection overlap. This ensures constant load on the output, a major concern with tube amplifiers. As a further safety measure, the Cab-Bone incorporates a power-off feature called SafeMode which automatically diverts the input signal to output-1 if the power supply is ever disconnected or turned off by mistake.To reduce the 'cable spaghetti' between the amplifier, speakers, pedal board and back, Cab-Bone is equipped with a Slingshot input and output. Slingshot is Radial's easy to use remote control system that allows any footswitch to toggle switching of remote devices using just regular 1/4" guitar cables. The Slingshot remote input can be controlled by either momentary or latching contact closure.To add versatility, the Cab-Bone also incorporates a Slingshot output that can be used to remotely switch amp channels while switching cabinets. You could, for instance, connect the Slingshot remote output on the Radial Loopbone to toggle the Cab-Bone and go from a 2 x 12" open back to a 4 x12" half-stack. Connecting the Slingshot output to the amp as well would allow you to change the amp channel at the same time, allowing each cabinet to have its own EQ and gain.Add a Loopbone to the equation and with a single foot stomp you can introduce an effects loop, change speakers and change amp channels at the same time! Very cool! Now you can get those perfect tone combinations onstage quickly, and do it with one switch instead of a tap dance routine!Like all Radial products, the Cab-Bone is built tough to handle the road: 14-gauge steel, baked enamel finish, and high performance parts throughout. You get all of this in a compact enclosure that is ultra-quiet and completely transparent to the tone of your amp.Cab-Boneanother creative tool for making better music from the Tonebone tone fanatics at Radial.
|
|
Audix Cab Grabber Microphone Holder
$49.95
The Cab Grabber from Audix is an innovative miking solution for guitar amps and cabinets. Holding mics weighing up to 1 pound, the Cab Grabber works on cabinets with 14" or less depth. Keeps your mic precisely positioned.An innovative miking solution for guitar amps and cabinetsAllows for precise positioningSimple, elegant, compact, and easy to useNo tools requiredAdjustable, tension-heldMic arm hand tightens firmly into positionHolds mics weighing up to 1 lb.Works on cabinets with flat surface or recessed edgeWill clamp to side of cabinet or over topFits 814" cabinets and ampsDurable steel construction
|
|
Audix I-5 And Cab Grabber Package
$129
This microphone package conveniently combines an Audix i5 instrument microphone and the Cab Grabber for mounting it on the cab where it can be properly positioned. Audix i5 Instrument MicrophoneThe cardioid pattern Audix i5 instrument microphone is a dynamic mic with a smooth, uniform frequency response of 50Hz-16kHz with SPL handling of 140dB. It's versatile enough to handle a wide variety of applications and music genres. It sounds great on vocals, snare, and guitar amps, with a clarity that will astound you. The Audix i5 features a durable cast zinc alloy body, dent-resistant grille, and black E-coat finish. It includes a heavy-duty mic clip and carrying pouch.Cab Grabber Microphone HolderThe Audix Cab Grabber is an innovative miking solution for guitar amps and cabinets. Holding mics weighing up to 1 pound, the Cab Grabber works on speaker cabinets with 14" or less depth. Keeps your mic precisely positioned. And once you have your mic positioned for the best sound, you don't have to worry about it being bumped out of place.Cardioid patternSmooth, uniform frequency responsHigh SPL handlingDurable cast zinc alloy bodyDent-resistant grilleBlack E-coat finishCable: 55" (1.4 m)Accessories Furnished: Windscreen, Heavy-duty mic clip, and carrying pouchCab GrabberAn innovative miking solution for guitar amps and cabinetsAllows for precise positioningSimple, elegant, compact, and easy to useNo tools requiredAdjustable, tension-heldMic arm hand tightens firmly into positionHolds mics weighing up to 1 lb.Works on cabinets with flat surface or recessed edgeWill clamp to side of cabinet or over topFits 814" cabinets and ampsDurable steel construction
|
|
Randall Isolation 12 Speaker Cab
$399.99
Essential whenever or wherever you're unable to crank full performance volume and tone. The concept is simple. A speaker is mounted in a completely closed, hinged cabinet with a microphone suspended inside. The cab has 1/4" in and outs, as well as a mic out to the mixing console. For recording, Isolation lets you record your amp full out, reflecting your true tone without waking the neighbors or inspiring visits from the cops. 12" Celestion Vintage 30 speaker. 18"W x 18"H x 31-1/2"D.Retractable handle Celestion Vintage 30 - 12" speaker 10" gooseneck for mic support Mic not included, condenser mic recommended
|
|
Marshall Jvmc212 2X12 Guitar Extension Cab Black
$729
The Marshall JVMC212 is a guitar speaker cabinet designed using only the finest materials and constructed with tried and tested techniques. The JVMC212 extension cabinet can output 150W of power through its Marshall/Celestion Vintage and Heritage speakers.The Marshall JVMC212 cab offers you the optimum solution in 2x12 UK-built speaker cabinet quality. The JVMC212 cab is constructed from the finest Baltic birch plywood in the Marshall UK factory and hand covered in traditional and hard wearing elephant grained vinyl covering. The Marshall JVMC cab is loaded with the finest mix of Celestion heritage and vintage speakers that facilitate the depth and tone guitarists search for. This is a 2x12" extension cabinet that feels larger than life in the way only Marshall knows how to do. The Marshall JVMC212 speaker cabinet is suitable for most amp heads.
|
|
Gallien-Krueger 112Mbx Extension Cab For Micro Bass
$299
The Gallien-Krueger 112MBX Extension Cab for Micro Bass lets you hang on to your portability while extending the output of your MB150S or MB150E combo amp. At just 12 lbs., this small but mighty Gallien-Krueger speaker cabinet shares the same sealed aluminum chassis, steel grille, and 100W speaker with the combos. The optional MB Mic Kit lets you mount the 112MBX on your mic stand for greater projection. Gallien-Krueger gives you a 1-year warranty on speaker and a 2-year warranty on electronics with the 112MBX.12 lbs. Aluminum chassis Steel grille 100W speaker Optional MB Mic Kit lets you mount the 112MBX on your mic stand for greater projection
|
|
ZT Lunchbox Cab 1X6.5 Passive Guitar Speaker Cabinet Silver
$119
The Lunchbox Cab is built on the platform of ZT's highly acclaimed Lunchbox amplifier. It's a Lunchbox without the amp—a passive extension speaker, with the same solid-as-a-brick cabinet housing the same custom-design 6.5" driver used in the ZT Lunchbox amp.Weighing less than 7 pounds, the Cab can blast out over 120dB, and sounds great doing it. The Cab also features a phase switch to provide accuracy in any situation.Connect the passive speaker cabinet to the Lunchbox amp's external speaker output and build a Lunchbox stack (it's adorable—like ferocious puppies or kittens). Or spread them apart a few feet to create spatial imaging. Or go further and put the ZT Cabs on opposite sides of the stage and give your sound a dimension that will make the crowd's heads swim.*Note: Early production Lunchbox amps (serial numbers LB02 0000 1000 through LB02 0000 2999) are not optimized for use with the Lunchbox Cab. Please verify that your Lunchbox is compatible before you add a cab, particularly if you expect to play at very high levels.
|
|
Zt Lunchbox Cab 1X6.5 Passive Guitar Speaker Cabinet Silver
$119
The Lunchbox Cab is built on the platform of ZT's highly acclaimed Lunchbox amplifier. It's a Lunchbox without the amp - a passive extension speaker, with the same solid-as-a-brick cabinet housing the same custom-design 6.5" driver used in the ZT Lunchbox amp.Weighing less than 7 pounds, the Cab can blast out over 120dB, and sounds great doing it. The Cab also features a phase switch to provide accuracy in any situation.Connect the passive speaker cabinet to the Lunchbox amp's external speaker output and build a Lunchbox stack (it's adorable - like ferocious puppies or kittens). Or spread them apart a few feet to create spatial imaging. Or go further and put the ZT Cabs on opposite sides of the stage and give your sound a dimension that will make the crowd's heads swim.*Note: Early production Lunchbox amps (serial numbers LB02 0000 1000 through LB02 0000 2999) are not optimized for use with the Lunchbox Cab. Please verify that your Lunchbox is compatible before you add a cab, particularly if you expect to play at very high levels.6-1/2" DriverPhase SwitchRugged exterior
|
|
Blackheart Killer Cab Bh110 30W 1X10 Guitar Extension Cabinet
$149.99
The Blackheart BH110 Killer Cab is a guitar speaker cabinet made to mate with the Blackheart Killer Ant, or Blackheart Little Giant 5. A single 10" 1016B Eminence extension speaker co-designed by Pyotr Belov and Eminence and engineered to pull huge body out of the Killer Ant, Little Giant 5 and other smaller heads. Also held to high standards, the Blackheart Killer Cab is crafted from the same 15 ply (18mm) void-free plywood as the entire Blackheart Engineering amp range. The Blackheart BH110 Killer Cab features expertly applied, durable black tolex and, of course, boasts the tatto-ish charm of the BHE logo.16 Ohms 30 Watts power handling 15 ply (18mm) thick, void-free plywood construction 10" Blackheart Model 1016B by Eminence Speaker with British Voicing, optimized for closed back cabinet 2 x 16 ohm parallel speaker jacks
|
|
Peavey Windsor Head And Valveking Cab Half Stack
$749.98
The Windsor Tube Amp Head employs three 12AX7 preamp tubes and four EL34 power-amp tubes in a single-channel configuration to deliver 100W of the sound of rock's golden era with exclusive Peavey technology and reliability. While most amplifiers leave the EQ to the preamp section, the Windsor features Peavey's patented Presence and Resonance controls, which adjust speaker damping from tight to loose in the high and low frequency ranges, respectively. The Windsor also offers Peavey's patent-pending Texture circuitry for adjusting the response characteristics from modern Class A/B push-pull to vintage Class A sounds. The Texture control provides incremental adjustment for an incredible range of tone texturing and coloring. The Windsor also features a footswitchable gain boost, three-band rotary EQ on the preamp, master volume, footswitchable effects loop and high and low inputs. ValveKing 412 Cabinet - Straight Front The all-birch ValveKing Series 412 Cab features 4 - 12" ValveKing speakers, dual input jacks, rear-mounted speakers, and 400W continuous power handling.Windsor Head 100W all-tube watts Three 12AX7 preamp tubes Four EL34 power amp tubes Single channel Footswitchable gain boost Three-band EQ Footswitchable effects loop Master Volume Patent-pending Class A-A/B Texture control Patented Resonance and Presence control High and low inputs ValveKing 4x12 Cab Birch construction 16 ohms mono 4 - 12" ValveKing speakers Rear-mounted speakers 400W continuous power handling Dual input jacks
|
|
Ashdown USA 410H 1050W 4x10 8-Ohm Bass Cabinet
$1105.99
Hand-built at the Ashdown factory in Kentucky, the US Series 410H bass speaker cab combines massive performance with exceptional value. Constructed from locally sourced 3/4" birch ply, this Ashdown speaker cab is glued, pinned, and screwed for maximum strength and protected by rugged black Tolex for a life on the road. The drive units are also made in the US and feature classic ceramic magnet assemblies, paper cones, and hand-wound voice coils.
|
|
Ashdown Usa 410H 1050W 4X10 8-Ohm Bass Cabinet
$1105.99
Hand-built at the Ashdown factory in Kentucky, the US Series 410H bass speaker cab combines massive performance with exceptional value. Constructed from locally sourced 3/4" birch ply, this Ashdown speaker cab is glued, pinned, and screwed for maximum strength and protected by rugged black Tolex for a life on the road. The drive units are also made in the US and feature classic ceramic magnet assemblies, paper cones, and hand-wound voice coils.Packs 1050W of power handling in a 4x10 cabRoad-tough constructionHandmade in the U.S.
|
|
Gallien-Krueger 410Rbh 800W 4X10 Bass Cab With Horn
$899
The Gallien-Krueger 410RBH 800W 4x10 Bass Cab with Horn is a perfect cab to pair with the 400RB head. 8- or 4-ohm operation. 800W handling. 4 cast-frame 10" speakers plus horn. Switchable between biamp, full range with built-in horn power limiter for protection. The 410RBH cab is made of birch with black carpet covering, a 16-gauge steel grille, interlocking corners, nickel-plated casters, and dual front-loaded ports. 27-1/2"W x 23"H x 18"D. 92 lbs. 1-year warranty on speakers. 2-year warranty on electronics. 8- or 4-ohm operation 800W handling 4 cast-frame 10" speakers plus horn Switchable between biamp, full range Built-in horn power limiter for protection Birch cabinet Black carpet covering 16-gauge steel grille Interlocking corners Nickel-plated casters Dual front-loaded ports 27-1/2"W x 23"H x 1"D 92 lbs. 1-year warranty on speakers 2-year warranty on electronics
|
*************************************************************
If you didn"t find what you wanted look below for Cab Road in the Amazon Marketplace.
*************************************************************
 |
Road Ready RRMBRS412C Mesa Boogie 4 x 12 Amp Cas
List Price: $939.99
Sale Price: $615.99
|
|
|
RRMBRS412C Features: -Beefy, stackable ball corners.-Double anchor Industrial rivets.-Recessed, industrial grade latches.-Recessed, industrial grade handle.-Premium 0.38'' vinyl laminated plywood.-Tongue and groove locking fit...
|
Does toyota make a 4wd double cab tacoma with a LONG bed and the TRD OFF-road pkg?
some say they dont make the long bed with the off-road package, but some have told me the opposite
yes the guy that works next to me just bought a 2007
Case Mackie
Check out this page if you are looking for Case Mackie
|
Mackie MS1402-VLZ Dumbo Ears
$56.99
MS1402-VLZ Dumbo Ears let you mount your Mackie 1402 mixer in a studio rack or a rack mount case for protection against the rigors of the road.
|
|
Mackie Ms1402-Vlz Dumbo Ears
$56.99
MS1402-VLZ Dumbo Ears let you mount your Mackie 1402 mixer in a studio rack or a rack mount case for protection against the rigors of the road.
|
|
Mackie Profx16 Rackmount Kit
$59.99
This Mackie Rackmount Bracket Set lets you easily secure your ProFX 16 mixer into the rack gear case of your choice. Also makes setup and breakdown of your rig a lot easier.
|
|
Road Ready RRCFX16 Mixer Case for Mackie CFX16MKII Black
$159.99
Created for the pros, the RRCFX16 mixer case is made for the journey and built to hold strong in high-stress situations. Designed to fit the Mackie CFX16 Pro mixer, the RRCFX1 features a heavy-duty, removable cover crafted with a no-pressure design to protect your mixer controls. The unique low-profile base allows you to access the mixer's rear connection panel without removing your mixer from the case. A rear access door allows for easy AC connections.
|
|
Road Ready RRCFX12 Mixer Case for Mackie CFX12MKII Black
$124.99
Created for the pros, the RRCFX12 mixer case is made for the journey and built to hold strong in high-stress situations. Designed to fit the Mackie CFX12 Pro mixer, the RRCFX12 features a heavy-duty, removable cover crafted with a no-pressure design to protect your mixer controls. The unique low-profile base allows you to access the mixer's rear connection panel without removing your mixer from the case. A rear access door allows for easy AC connections.
|
|
Mackie Ppm608 8-Channel 1000W Powered Mixer
$699.99
The 8-channel Mackie PPM608 is a 1000W powered mixer that features Mackie's custom designed, dual 500W Class D Fast Recovery Amps. This powerhouse powered mixer will deliver maximum volume, distortion free! It's fast and easy to wire in and dial up a sweet mix with a complete set of professional mixing tools. The PPM608 Powered Mixer includes premium Mackie mic preamps, 2 built-in DI boxes, musical 3-band Active EQs, and In-Line Compressors. Plus, you can sweeten and tweak your mix with Mackie's Dual 7-band graphic EQs for Mains and Monitors and the 32-bit RMFX+ processor with 24 sane, useable effects like 3 sizes of warm or bright room and plate reverbs, rich chorus effects and a unique user accessible tap delay. 20 lb.Fully featured 8-channel, 1000W, Ultra-Light Professional Powered Mixer with onboard 32-bit digital RMFX+ processorDual 500W Mackie designed Class D, Fast Recovery power amplifiers32-bit RMFX+processor featuring 24 sane, useable reverbs, choruses, and tap delay for live applications8 premium Mackie mic preamps with 48V phantom power and TRS inserts (ch 1-6)Single In-line Compression (SIC) provides increased presence and punch for vocals and instruments2 stereo inputs with dual RCA and dual 1/4-inch line inputs for flexible connectivityMackie's Musical 3-Band Active channel EQ (80hz, 2.5kHz, 12kHz)2 built-in DI boxes for direct instrument connectionsSeparate Monitor and FX auxiliary sends12 segment LEDs for the Main and Monitor outputsDual 7-Band graphic EQ on the Mains and Monitor outputs for tuning rooms and monitor mixes3-Mode Amplifier for ultra-flexible routing, switchable as Mains Stereo L/R, Mono Mains/Monitor 1, or Mon 1 & Mon 2Precision Passive EQ for enhanced clarity and LF response with Mackie passive loudspeakersRugged metal handles built into the sides of the mixer case for easy transport from gig to gig.Classic Mackie rounded front chassis design. If the PPM rolls on its face during transport the controls are recessed and protectedUltra-Lightweight and portable20 lb.
|
|
Mackie Profx12 / Th-15A Pa Package
$999.99
The Mackie ProFX12 / TH-15A PA Package includes the Mackie ProFX12 Professional Compact Mixer with 6 mono/4 stereo channels and effects; 2 x Mackie Thump TH-15A 400 Watt 15" Powered PA Speakers; 2 Audio-Technica M4000s dynamic mics; and 4 mic cables. Mackie ProFX12 Professional Compact Mixer The ProFX12 is the perfect choice for smaller performing acts, solo performers or for small venues that dont have the budget or space for a ton of outboard gear. The ProFX12 has everything needed to make your gig sound great and is really easy to operate. Plus, USB I/O lets you record the show or stream music straight from a laptop. The Pro in ProFX stands for Pro. Professional tools, rugged build quality, small footprinteverything you need.The ProFX12 is loaded with six Mackie high-headroom, low-noise mic preamps, 3-band EQ, a built-in DI for direct connection of a guitar or bass, integrated Gig-Ready effects, precision 7-band GEQ and more. The ProFX12 has all the right tools, each and every one designed to sound great. Plus, everything is housed in an ultra-tough enclosure with additional impact-resistant sidecheeks, protecting your investment from the rigors of the road.Gig-Ready RMFXEffects The RMFX(Running Man FX) 32-bit effects processor brings Gig Ready, useable effects to your mixes. Why scroll through hundreds of bizarre effects, like ghost ambience? Yeah, like anyone even knows what that means. Or how about winners like delay+phaser2, which youll never use in a million years. Those other mixers will leave your fingers raw from all the scrolling you have to do. The RMFXprocessor features 16 solid FX that are known for their utility and usability. Small, medium and large room reverbs with a mix of warm and bright characteristics puts your mix in the right space. Simple, rich choruses and an array of practical delays enable you to create professional mixes without requiring a two-hour sound check. Basically, Mackie has delivered the choicest parts of a full rack of gear, right at your fingertips, that is easy to master, allowing you to look and sound really good at your next gig. Really, really good.Record and Stream via USB With all the right tools for the job, the ProFX12 allows you to create memorable mixes, but even with all those features, portability is paramount and you cant be burdened with lugging around additional equipment. No worries, integrated USB I/O takes the pain out of recording. Just connect the ProFX12 to a laptop, start up your included copy of Tracktion 3 Music Production Software (or almost any DAW software out there) and you can record the whole mix. You can even stream music from your laptop during breaks. Once you get home, record more tracks or use the ProFX12 to playback some tunes during your next party. Unless youre anti-social, dont have the right kind of place for a party or are just sick of buying food and beverages for everyone. In that case, you can play back whatever talk-radio show you listen to when alone.N
|
|
Road Ready Rrcfx16 Mixer Case For Mackie Cfx16mkii Black
$159.99
Created for the pros, the RRCFX16 mixer case is made for the journey and built to hold strong in high-stress situations. Designed to fit the Mackie CFX16 Pro mixer, the RRCFX1 features a heavy-duty, removable cover crafted with a no-pressure design to protect your mixer controls. The unique low-profile base allows you to access the mixer's rear connection panel without removing your mixer from the case. A rear access door allows for easy AC connections.Double anchor industrial rivetsRecessed, industrial grade latchesSpring loaded handleIndustrial grade rubber feetPremium 3/8" vinyl laminated plywoodTongue and groove locking fitLow profile baseRear access door
|
|
Road Ready Rrcfx12 Mixer Case For Mackie Cfx12mkii Black
$124.99
Created for the pros, the RRCFX12 mixer case is made for the journey and built to hold strong in high-stress situations. Designed to fit the Mackie CFX12 Pro mixer, the RRCFX12 features a heavy-duty, removable cover crafted with a no-pressure design to protect your mixer controls. The unique low-profile base allows you to access the mixer's rear connection panel without removing your mixer from the case. A rear access door allows for easy AC connections.Double anchor industrial rivetsRecessed, industrial grade latchesSpring loaded handleIndustrial grade rubber feetPremium 3/8" vinyl laminated plywoodTongue and groove locking fitLow profile baseRear access door
|
|
Mackie Onyx 1220I Bag
$49.99
This Mackie mixer bag uses high-impact, high-density foam and durable nylon to protect your Mackie Onyx 1220i mixer. Features a large outer pocket for accessories and a study, padded shoulder strap for easy transport.
|
|
Mackie Onyx 1640I Bag
$64.99
This Mackie mixer bag uses high-impact, high-density foam and durable nylon to protect your Mackie Onyx 1640i mixer. Features a large outer pocket for accessories and a study, padded shoulder strap for easy transport.
|
|
Mackie Th-15A Bag
$74.99
Protect and easily transport your Mackie Thump TH-15A with this heavy-duty, durable padded bag. Features a handy pocket for accessories.
|
|
Mackie Powered Mixer Bag
$59.99
This Mackie mixer bag uses high-impact, high-density foam and durable nylon to protect your Mackie PPM608 or PPM1008 powered mixer. Features a large outer pocket for accessories and a study, padded shoulder strap for easy transport.
|
*************************************************************
If you didn"t find what you wanted look below for Case Mackie in the Amazon Marketplace.
*************************************************************
 |
Mackie 402-VLZ3 Premium 4-Channel Ultra-Compact Mixer
List Price: $129.99
Sale Price: $99.00
Used From: $75.00
|
|
|
Until now, mixers built for low-input, two-mic or one-mic-and-a-guitar applications really skimped on quality. With their flimsy construction and dismal sound, they resembled and performed like children’s toys...
|
 |
Odyssey FZM244 Flight Zone Case For A Mackie Sr244 Console
List Price: $299.99
Sale Price: $219.99
|
|
|
Our heavy duty ATA Live Sound Mixer and Console Cases can handle the harsh realities of life on tour as well as constant short haul transport. Fits: Mackie SR24.4 mixer. Internal dimensions (not including inserts): 22...
|
 |
Marathon MA-CFX16 Flight Road Case
List Price: $212.00
Sale Price: Too low to display
|
|
|
Marathon MA-CFX16 Heavy duty mixer case for Mackie CFX16 Pro Mixer or other similar mixers. Made from high quality materials with outstanding reliability and all-around protection for your equipment. Specifications: Exterior Dimensions (closed lid ): 26" W x 19" D x 8" H...
|
*************************************************************
Build a Speaker box or case?
I have some speakers that were made for the ceiling that someone gave me. Here is a link to them http://www.mackie.com/products/sp400c/index.html
Can I build a box for these speakers so I can use them in a room instead of a ceiling and if so where can I go to get plans for this. I searched the internet, but just got back subwoofer stuff.
Thanks,
yes you can build a box for them and they will work, the biggest problem that i see is that they are designed for a 70 volt system that means that any audio signal is combined with 70 volts, they do this to allow for huge areas-voltage drops over distance, but by combining the audio signal with a higher voltage, it can travel farther distances, to get them to work at home you will need to open them up, you should find a transformer inside(like this-http://www.amazon.com/gp/product/images/B00009UH7Y/ref=dp_image_text_0/002-3446841-9486449?ie=UTF8&m=A5EKKVXU1T4N9&n=11091471&s=photo)
you will need to tie the speaker wire to two of the wires coming from the speaker, otherwise, it will be very quiet and you will think that the speakers or your amp is bad, you do not need the transformer for your application
US $6.74
